Our Pricing


(prices do not include parts, and may be subject to change based on model)

Retail Prices– As of September 2016*

Minimum Service Charge: $60

Disassemble & Evaluate: $200 for Long Block

Standard Block Services:

Bore + Hone Cylinder.............................................................$30 per Cylinder

Deglaze Cylinder.....................................................................$10 per Cylinder

Clean Block...............................................................................$60.00

Replace Freeze & Galley Plugs..........................................$30.00

Replace Cam Bearings..........................................................$50.00

Resurface Deck – “V” Block................................................$160.00

Resurface Deck – 4 Cylinder...............................................$120.00

Line Hone Main Bores...........................................................$200.00 (2 or 4 bolt - cross bolted mains extra)

Measure and Inspect Block..................................................$60.00 (main bores not included)

Check main line bore.............................................................$55.00

Miscellaneous Block Services:

Clearance Block for Stroker Kit......................................................................$150-$250

Machine Block for O-ring..................................................................................$180.00

Race Prep Block...................................................................................................$140.00

Fill Block – Hard Block.......................................................................................$175.00

Bore + Hone Single Cylinder up to 1mm or 0.040”................................... $70 (additional $25 per 1mm over)

Bore + Hone Single Cyl. up to 1mm or .040” (2 Stroke or Blind)............$85.00

Torque Plate Hone................................................................................................$75.00 (per side additional)

Sonic Test Block for Cylinder Wall Thickness.............................................$150.00

Standard Head Services:

Pressure Test 4 Cylinder.....................................................$70.00

Pressure Test 6 Cylinder.....................................................$100.00

Pressure Test V6 / V8..........................................................$70 per Head

Pressure Test Outboard......................................................Starting @ $120.00

Pressure Test Diesel............................................................Starting @ $150.00

Valve Job

4 Cylinder 8 Valve.....................................................$130.00 per Head

4 Cylinder 16 Valve...................................................$250 per Head

6 Cylinder 12 Valve...................................................$200 per Head

Diesel............................................................................$175 (starting at)

Adjust Valve Lash (solid buckets)

         4 Cylinder 16 Valve....................................................$225 per Head

Replace Valve Stem Seals

8 Valve.........................................................................$30 per Head

Replace Valve Stem Seals DOHC..................................$60 per Head

Resurface Head

4 Cylinder....................................................................$80.00

6 Cylinder....................................................................$110.00

Diesel...........................................................................$160.00 (starting at)

 Miscellaneous Head Services:

Port + Polish Head

Stage I.........................................................................$130 per Head* 

Stage II........................................................................$325 per Head**

Stage III.......................................................................$650 per Head***

Machine Head for O-ring V8...........................................$190 per Head

Cummins - Machine Rocker Arm Pedestals for Head Studs................$60 ($10 per)

 *Stage I: Clean up bowls and port-match intake

**Stage II: Full port and polish without drastically making ports larger

***Stage III: Full race port

Miscellaneous Engine Services:

R & R Pistons on Rods....................................................$15 each

Resize Connecting Rods................................................$20 each

Balance Rotating Assembly...........................................$275.00

Resurface Flywheel (flat, no dowel pin).....................$60.00

Resurface Flywheel (stepped)......................................$70.00

Resurface Large Truck Flywheel (flat)........................$85.00

Resurface Large Truck Flywheel (stepped)..............$95.00

Flywheel Dowel Pin R&R................................................$5 each

Polish Crankshaft..............................................................$75.00

Resurface Manifold

Intake.........................................................................$125 – 4 Cylinder, $225 - V8

Exhaust......................................................................$50 – 4 Cyl ea, $60 6 Cyl ea

Cylinder Sleeve Install.....................................................$175 + Sleeve

Darton Sleeve Install

Honda B-Series......................................................$1600 w/ sleeves

LS based...................................................................$2500 w/ sleeves

Other..........................................................................Call for pricing

Dynamometer:

Chasis Dyno Testing*.......................................................$80 per 3 Pulls

Engine Dyno Testing.......................................................$500 3 Pulls

Engine Dyno Tuning........................................................$180 per Hour

Dyno rental (in shop only)..............................................$110 per Hour

 *Chasis “DYNO DAY” group discounts start at 10 vehicles  (must be scheduled in advance)

 

*Do to staffing and increasing work flow RPM will not be doing custom fabrication or machining as of 2/1/18*

 

Welding:

Basic Welding Repair......................................................$45 Minimum, $90 per hour

Fabrication & Welding....................................................$90 per hour, deposit as required

Welding Aluminum Head/Block Repair.....................$90 per Hour, $200 minimum

 Custom Engraving:

Valve Cover......................................................................................$60 per Cover (possible design fees may apply)

Various Components (ex. Intakes, tools, firearms)...............$90 per Hour (covers design and engraving)

 Custom Machining:

Custom Machining price starts at $90 an hour, and is to include research, development, design, and prototyping. Cost of duplicate parts, or multiple parts made, will be determined by the individual project.

*All prices subject to change without notice*

 

“Speed costs, how fast do you want to go?”